Loading... Please wait...

Categories

North Water Interior Mount Cockpit Bags (pair)

  • Image 1
  • Image 2
  • Image 3
  • Image 4
Price:
$140.00
Brand:
Current Stock:
5


Product Description

These cockpit panniers utilise easy to reach space while out paddling.

  • Helps keep your deck clear for drier paddling
  • Provides secure under deck storage
  • Items you may need while on the water are in easy reach
  • Easy in and out thanks to the SRB Mounting System.
  • Large #5 YKK zipper with 2 zipper pulls runs corner to corner along the top
  • Mesh drainage panel
  • 3 Mounting Options
    • A) onto the rudder cable housing
    • B) SRB Mounting System(TM) with quick release buckles
    • C) Bolt on for Polyethylene kayaks

Contents:

2x Cockpit Bags (panniers)
4x Vinyl mounting patches plus buckle

Care Instructions:

Clean salt, sand, and grit after use with fresh water. Do not store the product in damp conditions. Inspect the product for damage both before and after use. Do not abuse or apply undue stress to the product. Do not expose the product to long hours of direct sunlight. Identify your name on the product in case of loss. 

Important: When installing into a polyethylene (roto-molded) kayak you will need stainless steel nuts, bolts, washers (not included)

INSTRUCTIONS

These bags allow you to use the space at the sides of the cockpit. They are detachable and angled to fit the contours of the deck. It is easy to access and gives you a great place to store gloves, sunscreen, snacks and other daily necessities.

Note: Read over these instructions thoroughly.
This entire project should be done in a well ventilated area. Poor air circulation within the kayak will cause mineral spirits vapours to linger longer. Installation is quite simple and should only take you about 20 minutes.

Mounting Instructions (Composite Boats)

Needed for Installation:

  • Pencil or felt marker
  • Mineral spirits
  • Vinyl adhesive (eg. Vinyl-Tec 2000)
  • Newspaper
  • Piece 80 to 100 grit sandpaper
  • Clean-up rag
  • Heat gun or hair dryer (optional)

Locating Attachment Points for Vinyl Anchors

  1. Fill the bag with crumpled newspaper so it takes its natural shape.
  2. Fasten the vinyl patch buckles to the buckles on the bag.
  3. Hold the bag right way up in the position you wish to mount it.
  4. Once you are comfortable the bag is not going to interfere with your exiting the cockpit, note where the bag sits.
  5. Mark the outside of the vinyl patch. Repeat for each of the remaining patches.
  6. Follow the instructions on the vinyl adhesive to mount the patches. 

Mounting Instructions (Roto-molded or Plastic Boats)

Needed for Installation:

  • 4 stainless steel nuts, bolts and washers
  • Pencil or felt marker
  • Pair of scissors
  • Phillips head screwdriver
  • Adjustable wrench or similar
  • Drill and 3/16” drill-bit

Follow the above instructions from 1-5 above to determine the drill points on the hull.

  1. Prepare the vinyl patches by drilling a hole into the centre of the webbing between the two bar tack stitches. This will allow the bolt to pass through. Take a match or lighter and melt the edges of the hole to reduce fraying.
  2. Now, with the scissors you can either cut the vinyl from around the nylon or leave them as they are.
  3. Place the vinyl patch or webbing with the hole up against the inside of the hull and mark where you will drill the bolt hole. Carefully drill one hole at a time and bolt the webbing/vinyl patch to the boat. When bolting the vinyl patch to the boat ensure the buckle is facing the correct direction while tightening. 
  4. Now double check the second drill mark before drilling the hole. 

Product Videos

NW Underdeck Bag (02:35)
  • NW Underdeck Bag
Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...